To upgrade the software on your Satlink WS-6906 Go to product viewer dialog for this item.
, you will need to use a PC-based tool rather than a built-in menu option. This process allows you to update the device's firmware and satellite transponder data to maintain accuracy. Required Tools
RS-232 Cable: A specific RS-232 to USB or RS-232 to serial cable is required.
SatlinkTools / PC Updater: The specific upgrade program provided by the manufacturer or available from sources like Scribd. Firmware File: A valid .bin update file. Upgrade Steps
Connect the Hardware: Plug the RS-232 cable into your PC and the USB/RS-232 port Satlink WS-6906
Launch the Tool: Run the SatlinkTools or Updater program on your computer as an administrator. Establish Connection:
Click Confirm once the software detects a successful connection (e.g., "succeed connecting com1").
If the device is not detected, turn it off, wait 10 seconds, and turn it back on while the software is searching. Load Software: satlink ws6906 software upgrade
Click Load Software (or "Browser") and select your downloaded .bin firmware file. Confirm the upgrade by clicking Next or YES.
Wait for Completion: The process takes approximately 1–2 minutes. Do not turn off the power during this time, as it could brick the device.
Automatic Restart: Once finished, the finder will restart automatically, indicating a successful upgrade. Safety Warnings
Verify Hardware Revision: Ensure the firmware is compatible with your specific hardware version (V1 vs. V2). Using the wrong version can cause the "Lock" light to stay permanently lit or render the device inoperable.
Backup First: If possible, use the "Read parameters" function in the tool to save your current configuration to your computer before applying any updates. Satlink WS-6906 Software Upgrade Guide | PDF - Scribd
To upgrade the software on your Satlink WS-6906, you typically need to connect it to a PC using an RS-232 to USB cable and use specialized "SatlinkTools" or "Updater" software. While newer manuals may mention a USB-only method, the most common procedure for this specific model involves the following steps: Preparation
Hardware: You will need an RS-232 cable (often a 3.5mm jack to serial/USB). To upgrade the software on your Satlink WS-6906
Software: Download the SatlinkTools or Updater program and the correct firmware (.bin) file for your specific version (Early or Late model).
Administrator Access: If using Windows 7 or higher, run the updater program as an administrator. Upgrade Process (PC Method)
Connection: Connect the Satlink WS-6906 to your PC. Note that Windows may not "detect" it as a storage device immediately; this is normal.
Open Software: Launch the update tool and click "Browser" to select your downloaded .bin firmware file. Communication: Click "Next" or "Confirm" in the software.
If the software shows "CHECK SERIAL PORT STATUS," turn off the WS-6906 for 10 seconds, then turn it back on.
Execute Update: The software should now detect the device. Click "Load Software" or "Next" to start the transfer.
Completion: The process usually takes about one minute. The device will automatically restart once finished. Alternative USB Method (Manual-Specific) Step 3: Select the Firmware
Some newer versions of the WS-6906 allow for a direct USB stick upgrade:
Copy the firmware file to the root of a formatted USB flash drive. Insert the drive into the device's USB port.
Navigate to the System or Upgrade menu option and follow the on-screen prompts.
⚠️ CAUTION: Do NOT turn off the power or disconnect the cable during the upgrade, as this can "brick" the device. Also, ensure you are loading the correct firmware version, as loading the wrong file can cause the signal meter to stop functioning. If you'd like, I can help you: Find the official download links for the firmware.
Determine if you have an Early or Late model to avoid the wrong file. Troubleshoot connection errors (like "COM port failed"). Satlink WS-6906 Software Upgrade Guide | PDF - Scribd
.bin, .abs, or .img).Before you begin, you need to identify your hardware version and gather the necessary tools.
| Issue | Solution | |-------|----------| | Upgrade not starting | Reformat SD to FAT32, try another card (≤32GB). Ensure file is in root. | | “File not found” | Check filename matches exactly (case-sensitive on some versions). | | Stuck on boot loop | Reinstall firmware using a different SD card. Contact support if persists. | | Blank screen after upgrade | Hardware mismatch. Revert using original firmware from CD. |